Nov 04, 2026 Leave a message

Aochuang Hot Plate Welding Machine Standard Welding Process (Servo / Pneumatic Series)

info-681-855

 

This procedure applies to the full series of Aochuang servo and pneumatic hot plate welding machines, covering sealed fusion welding and structural butt welding of thermoplastic parts made of PP, PE, ABS, nylon (PA) and acrylic (PMMA). It applies to regular production products such as water filter cartridges, automotive plastic parts, home appliance housings and hollow plastic sheets. Following the principles of standardization, high precision and low defect rate, this procedure unifies equipment operation specifications, process parameter standards and working steps, and can be directly used as shop-floor work instruction, newcomer training material, quality control basis and a reference for standardized production implementation.

1. Pre-operation Inspection and Equipment Preheating (Preparation Stage)

1.1 Equipment Appearance and Safety Inspection

Before operation, inspect the machine frame, hot plate mold and upper/lower fixtures for looseness, deformation or damage; verify that the emergency stop switch, safety guard door and infrared protection device are sensitive and effective; check that the air pressure, electrical circuit and cooling system lines have no air leakage, electric leakage or water leakage, and that wiring is neatly arranged without aging or damage. In addition, clear debris from the workbench and remove oil, dust and residual adhesive from the mold surfaces, keeping the welding work surface clean and flat so as not to affect welding accuracy.

1.2 Process Parameter Setting and Preheating

According to the material, wall thickness and welding area of the workpieces to be welded, preset the core parameters on the equipment touchscreen: welding plate temperature, heating (melting) time, clamping pressure, holding time, cooling time and mold in/out stroke. After setting, start preheating: bring the hot plate to the set temperature and keep it at a constant standby temperature, with the temperature deviation controlled within ±3°C, so as to eliminate weak welding, burnt edges and uneven fusion caused by uneven temperature. For the first production run, conduct one to two dry cycles (empty-machine trial runs) to confirm that mold in/out, mold open/close and temperature control systems operate normally without abnormal noise or jamming.

2. Precise Clamping and Positioning of Workpieces (Loading Stage)

2.1 Take and Inspect Workpieces; Reject Defective Parts

Manually or via a robot, take the upper and lower plastic workpieces to be welded; check their specification and appearance, and reject defective parts with cracking, material shortage or deformation.

2.2 Lower Workpiece Loading and Fixture Clamping

Place the lower workpiece steadily into the dedicated lower-die fixture and activate the fixture clamping function to achieve precise positioning, ensuring that the workpiece has no offset or looseness.

2.3 Upper Workpiece Alignment and Suction Locking

Place the upper workpiece onto the upper-die fixture in matching alignment; it is automatically suction-locked, strictly matching the mating datum of the upper and lower workpieces to ensure welding concentricity and alignment accuracy.

2.4 Manual Recheck and Safety Door Closure

After clamping, manually recheck the alignment state, confirm that the workpieces fit the datum correctly without skew or risk of pressure marks, close the safety guard door, and enter the standby-for-welding state.

3. Hot Plate Feed and Constant-Temperature Melting (Core Fusion Stage)

3.1 Automatic Cycle Start and Hot Plate Feeding

Press the automatic start button; the machine enters the fully automatic welding cycle. The hot plate module advances at a steady speed and moves precisely to the designated position between the mating surfaces of the upper and lower workpieces, then automatically locks at the limit position once in place.

3.2 Mating Surfaces Pressed Against the Hot Plate

The upper and lower die fixtures advance toward each other synchronously and steadily, pressing the workpiece welding surfaces closely against the constant-temperature hot plate to start constant-temperature melting.

3.3 Constant-Temperature Melting and Real-Time Temperature Control

Heat strictly according to the preset heating time; heat conduction uniformly melts the surface layer of the mating plastic and forms a uniform molten layer. Throughout, the temperature control system fine-tunes the temperature in real time to ensure even softening of the fusion face, guaranteeing sufficient melt depth while avoiding high-temperature burning, flash overflow and material carbonization.

3.4 Slight Retraction After Heating to Separate from the Plate

When the heating time ends, the upper and lower fixtures automatically retract slightly to fully separate the workpieces from the hot plate, leaving a safe plate-retraction clearance.

4. Hot Plate Retraction and Rapid Mold Closing (Butt-Joining Stage)

4.1 Hot Plate Retraction to Standby Position

After the workpieces leave the hot plate, the machine quickly drives the hot plate module back to its initial standby position. Retraction must be smooth, steady and free of jitter or jamming, avoiding scraping the molten workpiece surface and eliminating defects such as stringing, material sticking and deformation.

4.2 Rapid Accurate Butt Joining After In-Position Signal

Once the hot plate fully retracts and triggers the in-position signal, the upper and lower fixture modules immediately and accurately close together, pressing the molten surfaces tightly together to achieve gap-free butt joining.

4.3 Flexible Progressive Pressure Application

The whole process adopts a flexible, steady-speed pressure mode; pressure is applied progressively to prevent workpiece misalignment, thin-wall deformation and excessive flash caused by instantaneous high pressure.

5. Constant-Pressure Holding, Cooling and Solidification (Shaping Stage)

5.1 Constant-Pressure Holding for Molecular Fusion

After mold closing and butt joining, the machine enters the constant-pressure holding stage, maintaining the set constant pressure throughout without pressure release or offset, so that the molten plastic molecules fully fuse and interpenetrate.

5.2 Preset Cooling Duration with Forced-Air Solidification

Solidify at constant temperature for the preset cooling duration; the equipment forced-air cooling system accelerates interface shaping, quickly dissipating residual welding heat and improving joint structural strength and sealing performance.

5.3 Real-Time Monitoring and Automatic Deviation Correction

During holding and cooling, the system monitors pressure and stroke parameters in real time and automatically corrects minor deviations, ensuring welding consistency of every batch and preventing defects such as loose joints, air leakage, water seepage and cracking.

6. Demolding, Unloading and Cyclic Operation (Finishing Stage)

6.1 Fixture Release and Die Module Reset

When cooling and solidification complete and the finished weld reaches the required structural strength, the upper and lower fixtures automatically release; the upper and lower die modules separate in order and return to their initial positions.

6.2 Gentle Finished-Product Unloading

Remove the finished product manually or via a robot smoothly, handling it gently to avoid joint cracking caused by pulling or collision.

6.3 Automatic Reset and Continuous Cyclic Operation

On completion of one cycle, the machine automatically resets to standby and can directly proceed to clamping of the next workpiece group, entering continuous cyclic welding operation.

7. Finished-Product Self-Inspection and Equipment Shutdown Procedure

7.1 Finished-Product Self-Inspection

For every batch, the first part must pass appearance and performance self-inspection: check that the weld joint is flat with no burnt edge, weak weld, crack or large-area flash, and sample-test sealing performance and tensile strength. Batch production may start only after the first part passes; during mass production, conduct periodic patrol inspections and fine-tune process parameters in time to stabilize the yield rate.

7.2 Shutdown and Cleaning

After daily operation, clear all materials from the workbench and clean residual adhesive chips and stains from the hot plate and molds to keep them smooth. In sequence, shut down the heating system, equipment power supply and air circuit valve; apply dust protection to the machine and record the daily equipment maintenance log.

8. Core Advantages of the Process

8.1 Full-process Control

The servo drive precisely controls stroke, pressure and speed; temperature control is stable and constant, and process parameters can be stored and recalled, supporting flexible production of multiple product categories.

8.2 Stable Yield Rate

The standardized melting, mold closing and holding processes eliminate manual operation errors, delivering extremely high batch welding consistency.

8.3 Wide Adaptability

Temperature and holding parameters can be flexibly adjusted according to plastic material, wall thickness and softness/hardness, suitable for both precision small parts and large thick-wall workpieces.

8.4 Safety and Efficiency

The fully automated cyclic operation, combined with multiple limit stops, overload protection and infrared safety protection, balances production efficiency with operating safety.

Send Inquiry

Home

Phone

E-mail

Inquiry